OnboardScales.com
Onboard Scales for Trucks and Trailers Galbreath AF Roll-off Onboard Scale System Sales, Service & Parts for:
Dump Truck Scales Logging Truck Scales Holland ILS fifth wheel Scale General Trucking Scales Vulcan Onboard Scales Cardinal Scales
Roll-off Truck Scales Refuse Truck Scales Aggregate Truck Scales Fifth wheel Scales Ez-Scale CAS Scales
Straight Chassis Scales Tipping Refuse Scales Trailer Filling Scales LoadRunner Scales Intercomp Scales
TradeRoute HL Scales Legal for Trade Truck Scales Underbody Truck Scales Air Ride Truck Scales Precision Loads Scales PNT Scales
Deflection Transducers Spreader Scales Forklift Scales Wheel Weigher Scales SI Scales MSI Scales
Refuse Front Fork Scales Concrete Truck Scale SI Tuffer Scales LoadPro Scales Avery-Weigh-Tronix Scales Rice Lake Scales
Replacement Parts Vac Truck Scales Ez-Scale Wheel Loader Scales Logging Scales LoadPro Scales VPG Onboard Scales
Onboard scale systems allow optimum, safe use of a truck’s payload capacity both for maximizing loads and preventing the liabilities of overloading.
USA Sales :1-844-476-2422  
Direct Line:1-330-476-2422  
Quotes@OnboardScales.com
Sales@OnboardScales.com
Celebrating 30 years of Service in the Scale Industry
International Sales: ApexEgroupLLC@gmail.com

PNT Long-Logger Truck Scales
 
PNT Long-Logger Truck Scales
High-Accuracy On-Board Weighing Systems For Logging Trucks

Complete Long Logger Kit:
1- PNT 2100 indicator w/ manual
2- 8705 Transmitter 2 leads
1- 216-80 Truck Cable
1- 216-35 Truck Cable
4- 532623 26" Load Cells
4- Load Cell Mounting Kits

Hauling Timber Product?
Avoid the cost of underloading and overloading and ensure maximum safe and legal payloads on every tractor and trailer—every trip
Accurate and reliable payload measurement is an important element of profitability and operating safety bulk hauling. Whether for municipal, county, state or private operations, on-board scale system allows optimum, safe and legal use of a truck's payload capacity-both for maximizing loads and preventing the liabilities of overloading.

PNT 2002 TRANSCODER: The PNT 8705 transcoder converts analog voltage from the load cells to a digital signal and transmits it to the meter over a single-line, two conductor cable. The Two-wire system provides reliable noise immunity, long term stability and allows use of a low cost connector between tractor and trailer. All cables use molded poly-nylon waterproof connectors rate to –55 degree F. The enclosure is heavy-gauge stainless steel.

Pacific Northwest Technologies AccuLink transcoders use 16 bit-per-input processing for high quality resolution of analog load sensor measurements.
Two-wire communications provide reliable digital transmission of weight data to the cab.
Transmitter circuitry is completely encapsulated inside a heavy gauge stainless steel enclosure for maximum environmental durability.
The time-proven Pacific Northwest Technologies ConxLink connection system is the best method in the industry for protection against moisture, corrosives, and other harsh environmental conditions.
Available in 1,2,3,4,5 or 6 inputs.

The Model 2100 In-cab Meter from PN Technologies is used in all on-board scale applications requiring dual channel weight displays. Total vehicle weight is displayed as well as individual tractor and trailer weights. The PNT 2100 meter can be set to cycle automatically between individual channel weights and total weight displays. The operator can press the cycle button at any time to stop and monitor any channel desired.

  • 100 % Compatible with SI-9100GW.
  • Two channel models for long and short loggersB-trains and chip vans.
  • LargeSuper-Bright Red seven-segment LEDs Display.
  • Two-wire (non-polarity sensitive) digital technology.
  • An Advanced Calibration function for calibrating the scale without a load.
  • Rugged and reliable design tested over all environments.
  • Quick and simple calibration.
  • Simple diagnostics allow quick testing of each system component.
  • Compatible with all models of On-board scale load cells and sensors.
  • Transcoders built of heavy-gauge stainless steel.
26" Shear Beam Load Cell (12,500 lb) w/Bearing Plate
Installed and painted
1 Load cell on each side of the bunk
A modern on-board weighing system consists of load cells to sense the load’s weight, transmitters and cables to send the load-cell output to the indicator, and an indicator to change the signals into information usable by the operator. Load cells are precision-machined high-strength steel beams with strain gages bonded inside. The load cell is installed on the truck between the load receiving deck and the truck frame. When loads are applied to the truck, the strain gages sense the weight of the load and send a small electrical signal to the indicator by way of the transmitter. The transmitter provides the voltage to the load cell to power the strain gages. A signal voltage from the load cell is returned to the transmitter where it is converted to a digital signal before being sent to the PNT 2100 indicator through the two-wire cable.
No more Overweight Fines: The expense of operating overloaded is already prohibitive in many regions and is becoming a serious issue nationwide. Enforcement is increasing and penalties are becoming more costly.
Eliminate Legal Liabilities: The potential costs to a hauler from lawsuits resulting from an accident involving an overloaded truck can be severe.
Ensure Operating Safety: Overloaded trucks have significantly impaired braking distances and cornering abilities, and are more likely to experience premature failures of truck components.
Cut Maintenance Costs: Hauling legal payloads reduces maintenance expense on springs, brakes and tires, and increases the operating lifetime of the truck and body.
Increase Driver Efficiency: Our on-board scales give your drivers the assurance of hauling legal. With scales, drivers finish routes more efficiently and faster with full, legal loads.
Notice drop ship: (Shipping included in price)
Model Description Notice Est Wt. Price
PNT-Long-Logger 1-PNT2100 Indicator w/Manual, 2-Transcoder 2 leads, 1-216-80 Trailer Cable, 1- 216-35 Truck Cable , 4- 26" Load Cells, 4- Load Cell Mounting Kits non-refundable. 200 lbs Call

 

 

 

OnBoardScales.com
Direct Line - 1-330-476-2422
CopyRight © All Rights Reserved
Installable Systems/Parts/Made to Order or Configured to order: Are NON-Refundable
No Customer Data stored on our server.
Prices subject to change without notice
OnboarScales.com Home Page
We record all calls for quality assurance.
Celebrating 30 years of Service in the Scale Industry.
Customers can contact us at emails listed below
Quotes@Onboardscales.com
Backup Account/International: ApexEgroupLLC@gmail.com
 

Receive 3% discount if paid by check or wire transfer